Moment of honesty: If you buy something through our posts, we may get a small commission. Read more here.

How to use a Bandsaw

If you want to use a bandsaw for woodworking, there are several things you will need to know before getting started. The following steps will allow you to use this tool without properly so you can get the best results.

The steps to use bandsaw properly

Select the Proper Blade

The next thing you’ll have to do is choose the appropriate blade to use with your bandsaw. This will depend on the specific task you need to perform. A ½ inch blade is usually acceptable, but you’ll need to consider your requirements before making a decision. If you don’t use the right blade, you will have major problems with getting ideal results.

Set the Blade Tension

It is also very important for you to set the tension of the blade. Many of these power tools have dials that you can use to do this quickly and easily. The tension that you choose will depend on the specific blade you are using. Setting it too low can lead to excessive movement, which will make it impossible to cut properly.

You also don’t want to set the tension too high, because it could snap. If you aren’t sure about the tension, you should refer to the manufacturer’s instructions. This is a step that you do not want to mess up, because it will make using the saw difficult and unsafe.

Set the Speed

You need to set the speed that you want to work with on your bandsaw as well. Not all of these saws have variable speed options, but it is good to have one that does. This will give you more versatility with the work you do. If you are going to buy a single-speed saw, you should get one that is set at 3000 FPM. Make sure that you choose a speed that is conducive to the type of cutting you’ll be doing. This is one of the best ways to ensure quick and efficient cutting.

The Guides

The guides on the bandsaw’s blade are responsible for keeping it level and in place at all times. There are guides on the top and bottom that you will need to set close to the blade before getting started. This will ensure that the blade doesn’t move around too much while you are cutting, which can be dangerous. It can also negatively impact the quality of your work.

Plug it in

Once you have made all of the previous adjustments, you can plug in your bandsaw. It is a good idea to keep it unplugged when not in use.

Begin at the Shallowest Angle

Whenever you are doing a contoured cut, it is a good idea to start at the shallowest possible angle. If you are working with a piece of wood with two shallow ends, you’ll want to start at both and work your way into the middle. By doing this you will prevent any of the edges from becoming ragged.

Always Measure Twice

One of the best rules to follow when it comes to using a bandsaw is to measure twice and cut once. It is very important that you measure out each piece and mark it with a pencil before you begin cutting. This will reduce your chances of making any mistakes that you’ll regret later on. You want all of the lines you make on the wood to be as straight as possible. This will make the actual cutting a lot easier overall.


When you start doing the actual cutting, remember to never force the wood into the teeth of the blade. You want to be very gentle when you are pushing it into the blade because otherwise, it is very easy to make mistakes. If the blade isn’t very sharp, you can feel free to apply a little bit more force. Just use your best judgment when it comes to how much pressure to use.

You also need to keep a close eye on where your hands are at all times. Losing focus for even a second can result in serious injury.

Remember to let the saw come up to speed by starting slow and working your way up. It won’t take very long for it to start cutting through the wood faster. One of the biggest mistakes people make with these saws is to push too hard when they are first starting. This can ruin the design you are trying to cut out.


Once you are all finished using the saw, you will want to unplug it and take the blade out. You can do this by simply loosening the tension. Make sure that you put your blade into storage until you need to use it again. It’s also a good idea to clean the saw off so you won’t have to do it before using it next time.

bandsaw maintenance

Tips & Warnings to safety use a bandsaw

Clean it Off

The first thing you will need to do is clean any dust and debris off your bandsaw. This will ensure that you can get the best possible performance from it. Give it a thorough wipe down before doing anything else.

Always keep your machine serviced correctly and clean. Remove accumulated dust from dust exhaust tubes, and oil the blade guide bearings frequently.

The Blade Guard

Whenever you are cutting with your bandsaw, you have to make certain that the guard is close to the material you are working with. Set the guard at the right level before making each cut so you get it right the first time.

Put Your Safety Glasses on

It is very important that you wear safety glasses or goggles while operating a bandsaw. This will protect your eyes from getting injured from flying debris. It will also help keep sawdust out of your eyes, which can make it difficult to focus on what you are doing. It’s also a good idea to wear gloves to protect your hands as well. While gloves won’t do much to prevent your hands from getting cut if you slip, it will protect them from sharp debris. Even small pieces of wood can cause serious injury when flying at a high rate of speed from the blade.

Check all the needed clearances for your cut

You do not want to be halfway via the cut only to find the workpiece which will not turn or feed-through completely and it is now to plug your saw in.

Make your cut

If you want to turn the saw, then permit it to come up to speed and note that the blade is traveling in a straight true line. If there is any observable wobble or deflection in the blade, the stop and recheck the assembly of the band saw for the proper adjustment.
Please mind that you need to keep your fingers as far as possible from the bandsaws blade as a safety purpose and feed the stock so that the blade follows the cutting which you have made in it.

Mark out your cut on the wood stock you are using

You need to make a clear, easily distinguished lines on the wood materials, using either a soft lead pencil or a marker which is suitable for the marking on wood materials. Here do not use an ink marker on the wood which is to be naturally finished or stained with a transparent stain.

If you still haven’t picked a good bandsaw, feel free to check out our best band saw guide.


We will be happy to see your thoughts

Leave a reply